Are line output converters necessary?

If you plan to have an amplifier added to a factory-installed audio system, chances are you’ll need a line output converter. It’s even more likely that you’ll need one that can provide a remote turn-on signal for that new amp.

What does a 2 channel line output converter do?

Can you hook up subs to a factory amp?

Use a Converter

This is because the factory head unit generally tends to have speaker wires but does not have a preamp output that can convert them into RCA signals. This converter can make it highly convenient for you to connect the factory radio to the amplifier and subwoofer.

Are line output converters necessary? – Related Questions

Can I connect subwoofer to normal amplifier?

To get started with the actual hook-up, you’ll connect the subwoofer to the amplifier using the RCA cable. If you want a stereo hook-up, you’ll need two sets of RCA cables. Connect the subwoofer output to the amplifier input.

What does a line output converter do?

Q: What is a line output converter? A: A line output converter, or LOC for short, converts a speaker-level output signal into an RCA preamp-level signal. This lets you connect the radio to the amplifier. It can also be used to connect a new radio to a car’s factory amp (see below).

What do you need to install a line output converter?

How do you install a line out converter to a factory amp?

How to Install a Line Output Converter
  1. Disconnect the negative battery terminal. Disconnect the negative battery terminal.
  2. Remove your factory head unit.
  3. Review your wiring diagrams.
  4. Strip Wires and Make the Proper Connections.
  5. Test your System and Tidy Up the Install.

Does Best Buy install line output converters?

Thank you for your question! We do install line output converters and amps in most vehicles. It can vary depending on the unit you’re looking at and the vehicle it’s going into. I would recommend connecting with your local Best Buy’s Autoteam team to get started for this.

Can I use factory amp aftermarket?

Whether your factory amp has all-analog or digitally controlled inputs, you can use its powered output signals for your aftermarket amp’s inputs. This way, each channel of your new amp will play whatever the old amp channel was playing.

How do you hook up a amp to a factory amp?

The best way to connect it to a factory system is to tap into the stereo’s speaker outputs for the amp’s input signal. Then send the amp’s outputs back to the stereo’s harness, and on to the speakers through the factory wiring.

Do all amps work with all subs?

Multiple subs wired together must be the same coil type and impedance. If they’re not, the power won’t divide evenly between them, and some subs would probably be over-powered while others get under-powered. If you want to run different types of subs in a system, each type needs to have its own separate amp.

Do I need to bypass factory amp?

By bypassing the factory amplifier, the music sounds more detailed and clear than it did when he used the amplifier integration harness. Whenever there’s one available, we recommend bypassing the factory amp to get better sound. If you’re considering a new stereo for your vehicle, keep this option in mind.

Is it OK to leave an amplifier on all the time?

But a purely electronic piece like a power amp or preamp are better left powered on at all times – with but few exceptions. So, keep the lights on with your equipment – it helps everything live longer and sound better.

Can you run an amp without an inline fuse?

Some amplifiers don’t have internal fuses. In this case, check your amp’s power ratings to determine the proper size fuse. If your amp doesn’t have an internal fuse, or you have multiple amps without built-in fuses, consider using a fused distribution block.

What should you not do with an amplifier?

Never, never, never run the amp with no speaker plugged in. This can cause major damage. Do not flip the power switch off, then back on rapidly. This can cause power supply damage.

Can an amp be too weak for speakers?

If you don’t have a powerful enough amplifier to reach the volume levels you want, you can damage the speakers by feeding them too much high-frequency energy by driving the amplifier into clipping. It’s the extra power in these harmonics that damages speakers.

What happens if you turn on a tube amp without a speaker?

Usually the tubes will go into a growing oscillation that eventually burns them. Most of the time the output transformer is ok, but if left on long enough it can also be damaged. And playing through an unloaded tube amp will only speed up the road to damaging the amp.

Leave a Comment