Good quality sound for a good price. Stylish design with a lighted logo makes it look better than the average amps. Planet Audio is a good brand as I have tested this amp, a 1 channel amp, 12″ subs, 3-way 6×9, 6 1/2 combos, and their 10 farad cap no problems at all.
Boss International Group is the manufacturer of 3 major car audio brands, Boss Audio, Planet Audio, Sound Storm Laboratories plus NYNE Bluetooth speakers. We have been in business for 30 years and we are still growing.
How do you know if your gain is too high?
If the gain is too high at the input stage, your audio will reach the point of distortion or clipping. This can be a good or bad thing depending on what you are going for, as you might want to get some distortion with an amplifier, though you might want a clean tone for digital audio.
Are Planet Audio amps good? – Related Questions
Where should I set the frequency on my amp?
Set the crossover point around 10 Hz below the lowest frequency your speakers can produce without issue. (keep in mind that the most common recommendation for crossover frequency is 80 Hz). Once again, play some music. But this time, slowly turn up your receiver’s volume until you hear it begin to distort.
What should the settings on my amp be?
Generally, good rock guitar amp settings are:
Gain: 5-7.
Treble: 5.
Mids: 6.
Bass: 6.
How do you set a good sound amplifier?
Turn the receiver volume down. Set the receiver’s fade control all the way to the rear speakers. Again, turn the receiver’s volume up to ¾ full and turn up the rear gain control of your amp until the music distorts, then turn it down so it plays clean again. Turn the receiver volume down.
How do I get my planet amp out of Protect Mode?
How to Get Amp Out of Protection Mode:
Disconnect Speakers.
Check the Temperature of the Amp.
Unplug the Head Unit.
Check the Ground Connection.
Check All Cables.
Check Impedance Load.
Reset the Amp’s Gain.
What happens when your amp goes into protection mode?
Amplifier protection mode is a shutdown state that car amps may enter in certain situations. The purpose of the shutdown state is to prevent damage to the amp or other system components. So while dealing with an amp in protect mode may be annoying, it might save you from a bigger headache down the road.
How do you know if your amp is in protect mode?
How do I know if my amp is blown?
The most common aural indication of a blown speaker is an unpleasant buzzing or scratching sound, by itself or roughly at the pitch of the note the speaker is attempting to reproduce. Or there could be no sound at all.
What causes an amp to burn out?
the amplifier is malfunctioning
If a component dissipates too much heat, or experiences excessive voltage, it may start to burn up.
Does leaving an amp on damage it?
Leaving guitar amp on is bad for a guitar amp’s life. The tubes in an amp would get damaged and can also result in overheating which can lead to other serious issues.
How do I know my amp is fried?
Test the sound by unplugging the sound cables or colored RCA wires.
Hissing and crackling are often easy to fix by rearranging the wires or getting complimentary speakers.
If the noise doesn’t stop, then you probably have a faulty amp to replace.
What does a blown amp sound like?
The most common aural indication of a blown speaker is an unpleasant buzzing or scratching sound, by itself or roughly at the pitch of the note the speaker is attempting to reproduce.
How do I make my amp tone crunchy?
Although you can get a crunch tone with pedals, it came about by running an amp hard and pushing it past it’s happy clean sound. The first way to achieve a crunch tone is by pushing the amp with pedals. A boost pedal does just what the name implies. It boosts the signal coming from the guitar.
Can amplifiers be repaired?
Modern audio equipment is built using delicate components that cannot be repaired; instead, they are replaced. Your audio professional will know which ones to replace, where to get them, and how to do the job. Use a clean pencil eraser to clean cable pins on a regular basis.
What can damage an amplifier?
The two most likely possibilities for damage are: – Connecting the speakers incorrectly, putting a heavy load on the amplifier and overheating it. Usually one channel goes before the other. – Cranking up the volume on the amp and ruining loudspeaker driver(s).
Will an amp still turn on with a blown fuse?
If the fuse is present and blown, the amp can’t turn on because the circuit providing mains voltage is open. Simply replacing the fuse may or may not solve the problem.
Why does my amp shut off when it hits hard?
If your amp cutting out at high volume, there could be loose connections in the power wire, ground wires, or speaker wires. Make sure that all of these wires are firmly connected to the stereo and the speakers.
