Connect the RCA, speaker, and remote turn-on leads to your amp. Feed the RCA cable along the bottom of the doors, then plug it into the back of the amp. Once you’ve done this, plug the speaker and remote turn-on leads into the back of the amp. These wires may be different colors, depending on the manufacturer.
What is a big 3 upgrade?
The Big Three wiring upgrade
This upgrade replaces or augments three key cables in the electrical system with 1/0 or 4 gauge wires: the battery ground to chassis wire, the chassis to engine block wire, and the alternator plus to battery plus wire.
How do I hook up a fuse to my amp?
How do you hook up an amp to a car battery? – Related Questions
Can I power my amp from my fuse box?
You should not use a fuse tap to supply power for an amplifier — that would be dangerous to your vehicle’s electrical wiring. An amplifier requires a thick power cable to be run from the amp directly to the battery.
What does putting pennies in a fuse box do?
A penny is copper and an excellent conductor of electricity, so this appears to “fix” the problem with the fuse. We can’t overemphasize how dangerous this is. The problem is the penny will allow any amount of electricity through the circuit, rather than burning out like a fuse to protect the circuit.
Where do you connect the fuse?
The best place to install a fuse in a grounded power system is on the ungrounded conductor path to the load. That way, when the fuse blows there will only be the grounded (safe) conductor still connected to the load, making it safer for people to be around.
Which wire does the fuse connect to?
A switch or a fuse in an electrical circuit is always connected to the live wire so that the socket or appliance is not live when switched off.
In which wire should we connect fuse?
The fuse wire is always connected in the live wire of the circuit because if the fuse is put in the neutral wire, then due to excessive flow of current when the fuse burns, current stops flowing in the circuit, but the appliance remains connected to the high potential point of the supply through the live wire.
How do you connect a fuse?
Fuse is always connected to a live wire. If fuse wire is connected to neutral wire instead of live wire then even when the fuse burns out the appliance remains connected to the live wire and the current supplied will not be disrupted due to overloading.
Does it matter which way a fuse goes in a car?
It doesn’t matter which end of the fuse holder gets used for going to the battery and which goes to the jack. Fuses don’t require current to flow through them in a certain direction so either way is fine. But typically line is the side that the power comes in on and load is the power going out.
Which wire do you connect first?
Hot Wire. Hot wire is used as the initial power feed to a circuit. It carries the current from the power source to the outlet. Acting as the first instance of a circuit, they are always carrying electricity, meaning it is dangerous to touch a hot wire while there is a power source feeding it.
Why is fuse connected with live wire?
The fuse is connected to the live wire so that the appliance will not become charged (have a potential difference of 230 V) after the fuse has melted due to excessive current. Fuses must be fitted onto the live wire so that when it blows, it will disconnect (isolate) the appliance from the high voltage live wire.
What happens if live wire is not connected?
Without the earth wire, if a fault occurs and the live wire becomes loose, there is a danger that it will touch the metal case. The next person who uses the appliance could get electrocuted.
What happens if you join live and neutral?
When live wire comes in contact with the neutral wire, then the insulation of wires is damaged or there is a fault in the appliance. In such a situation, the current in the circuit abruptly increases. This is known as short circuiting.
What happens if only live wire is connected?
A shock or fire would be highly likely. Even if a circuit is switched off (i.e. the switch is open), the live wire can still be dangerous. If you touch it, you may complete a circuit between the live wire and the earth (because you’ll be standing on the floor), so you get a shock.
What happens if you touch 2 live wires?
If you touch both cables at the same time, then your body becomes a conductor and the current of electricity will pass through your body. Also, if you touch a cable that has current flow and also touch an electric connection that is grounded, then you become the easiest path for electricity to go to the ground.
Can you touch a live wire if you’re not grounded?
conductor – your body, in this case – has to complete the circuit between the source of current and the ground. If you’re not grounded at all, no current will flow and you won’t feel a thing.
What happens if hot wire touches neutral?
A short circuit happens when a “hot” wire (black) touches another hot wire or touches a “neutral” wire (white) in one of your outlets. When these two wires touch, a large amount of current flows, creating more heat than the circuit can handle, so it shuts off.
