Is Dayton Audio high quality?

Throughout the years, Dayton Audio products have received acclaim worldwide and are often compared favorably to similar items costing far more. When people talk about reasonably priced, high-quality audio speakers and electronics, they talk about Dayton Audio.

Where is Dayton audio based?

Dayton Audio is based in Springboro, O.H.

How do transmission line speakers work?

Transmission line just takes the back waves generated from the speaker, inverts their phase, and throws them back in front of the speaker, to combine with the front waves. This is the main principle around how the transmission line works.

Is Dayton Audio high quality? – Related Questions

Do transmission line speakers sound good?

Because the transmission line is so well damped with acoustic foam in order to absorb the unwanted mid and high frequencies radiated into the cabinet, the quality of the bass produced by a transmission line speaker is also incredibly accurate and well damped, with greatly improved time-domain characteristics than is

How many amps go through transmission lines?

The largest transmission lines in use have a rating of over 4000 A per circuit, but the average current in a typical circuit is more like 700 A. Distribution lines typically have currents of hundreds of A or less.

How does a line array speaker work?

Simply put, a line array is a series of speakers covering the same frequency range placed in a line, typically vertical. The speakers are placed at slightly different vertical angles, which allows them to cover a greater area than one speaker by itself.

Why there is sound in transmission line?

When a corona forms, there can be audible noise coming from the transmission line. A crackling or humming sound is generated by small electrical discharges, often caused by water drops that collect on the conductor when it rains or when there is sufficient moisture in the air.

How is sound transmitted to speakers?

Speakers work by converting electrical energy into mechanical energy (motion). The mechanical energy compresses air and converts the motion into sound energy or sound pressure level (SPL). When an electric current is sent through a coil of wire, it induces a magnetic field.

How does a crossover for speakers work?

Audio crossovers are a type of electronic filter circuitry that splits an audio signal into two or more frequency ranges, so that the signals can be sent to loudspeaker drivers that are designed to operate within different frequency ranges. The crossover filters can be either active or passive.

What is the best crossover for speakers?

The most common crossover frequency recommended (and the THX standard) is 80 Hz. On-wall or Tiny ‘satellite’ speakers: 150-200 Hz. Small center, surround, bookshelf: 100-120 Hz. Mid-size center, surround, bookshelf: 80-100 Hz.

Do I need a crossover without an amp?

If your car audio system uses coaxial speakers, you probably don’t need an additional crossover. Full-range speakers already have built-in passive crossovers that filter the frequencies that reach each driver. Even if you add an amplifier into the mix, the built-in speaker crossovers should be more than sufficient.

What crossover should I set my speakers?

Set the crossover point around 10 Hz below the lowest frequency your speakers can produce without issue. (keep in mind that the most common recommendation for crossover frequency is 80 Hz). Once again, play some music. But this time, slowly turn up your receiver’s volume until you hear it begin to distort.

Why is 80 Hz the best crossover?

Most people cannot localize bass below 100hz. With the crossover at 80Hz, it ensures that most everyone will not be able to hear where the low bass is originating from. A higher crossover will compromise the realism for many people.

What Hz is best for subwoofer?

What is the recommended crossover frequency for a subwoofer? For home theater systems, 80 Hz is the recommended setting and the default setting out of the box. However, you can set the channel’s crossover between 40 Hz – 250 Hz based on which setting sounds best for your system.

Is 50hz good bass?

50 Hz is too high. You can use the Low Cut option of M-Class EQ, which cuts at 30Hz. If you can’t hear 50hz, its hard to mix it. And 50hz should be a subwoofer.

What Hz is the deepest bass?

Deep bass refers to the audio bandwidth between 16-80Hz. The range of frequencies is most commonly handled by a powered subwoofer receiving an audio signal from an AV receiver or other audio source component the cutoff limit of human hearing where sound enters the “feel zone”.

What frequency is punchy bass?

For a perceived punchy bass boost 80-120Hz and cut everything below 60Hz.

What dB is best for bass?

The paper states that “the range of preferred bass levels among individual listeners is 17dB, from -3dB (listener 346) to 14.1dB (listener 400).” This finding astounded me, not only because of the range of difference of 17dB — a lot — but that someone out there preferred -3dB of bass cut.

Is 40Hz good for bass?

Bass Frequencies and Other Instruments

While the fundamental range of the bass extends up to around 400Hz, most bass playing occurs with fundamentals below that between 40Hz and 200Hz. Though many non-bass instruments can play in their lower range, they’re not down there all of the time.

Leave a Comment