The Kicker speakers are less expensive, but the JL speakers sound better. 8″ speakers have more surface area and usually handle more power than 6.5″ speakers. The larger cone area and higher power handling mean that the 8″ speakers play louder and give you more mid-bass response than a 6.5″.
Are JL Audio subs good?
JL Audio is considered to be a high-end, high-performance sub-brand that produces quality sound products. As such, JL audio is usually worth the money for those looking for a top-quality product.
What are 12 inch subs good for?
The benefits 12-inch subwoofers provide over smaller ones are that they handle more power, play louder, and handle more bass. Many people also think they sound better than smaller subs.
How many watt amp do I need for a 12 inch sub?
A 12 inch sub woofer requires anywhere from 150 to 1000 watts in order to reproduce the sound at the same level that it was intended. This will be determined by the power rating of your speakers, but in general, you need an amp that can handle 300 watts.
Is JL Audio better than kicker? – Related Questions
What gauge of wire should I runs to a 12-inch subwoofer?
The speaker wires. If your sub system is going to put out more than 1,000 watts RMS, you can use 12-gauge speaker wire. But 16-gauge speaker wire works well for most installations.
Do subwoofers drain car battery?
The most common way a subwoofer can damage your car is by draining the battery. You’re adding extra strain to your electrical system when you put a subwoofer in your car. Sound vibrations take a lot of power to produce. The power required to run a subwoofer draws from your battery.
How many watts is a good amp for a subwoofer?
The best wattage for a small-room subwoofer is between 100 and 300 watts. Most homeowners find 100 watts sufficient enough. A subwoofer for larger rooms can be 400 watts or 600 watts. For high-end subwoofers, the standard is over 1000 watts.
How many watts should my amp be for my subs?
Two subs on a 500 watts RMS amp will want about 250 watts RMS each. So you’ll look for subs each rated for 250 watts RMS or more.
Is 1000 watts good for a subwoofer?
A 1,000-watt subwoofer doesn’t have to play any louder than a 100-watt subwoofer. The watt rating is a rough guide to how loud a subwoofer might be able to play, but it doesn’t have to be louder. You always control the volume. In fact, a 1,000-watt sub may sound better at “regular” room volumes than a 100-watt sub.
How do I know what amp I need for my sub?
Finding the Right Sub for Your Amp
The sub’s RMS watts rating must match the amp’s power range for optimal sound. Find the amp’s power in RMS watts at 4 ohms, 2 ohms, and 1 ohm. Choose the RMS power rating you’d like to achieve. Your sub’s total impedance will be the load impedance (ohms) of that rating.
What happens if your amp is too powerful?
Amplifiers can be too powerful for speakers. Speakers are limited by the electrical energy that they can convert into audio. As a general rule, if the amplifier produces more electrical energy than the speakers can handle, it may cause distortion or clipping, but damage is unlikely.
Is it better to have higher watt subs or amp?
No, It is always recommended to use approximately twice as much amplifier power as the speaker’s power rating. More watts may provide more bass, but only if the amplifier you’re currently using is insufficiently strong for the speakers you’re using.
Should I run my sub at 2 or 4 ohms?
A subwoofer with a lower electrical resistance produces a louder sound than one with a high electrical resistance, which means that 2ohm subwoofers are louder than 4ohm ones. Although louder, 2 ohm subwoofers are also more likely to produce a poorer quality of sound due to its’ power consumption.
What DB is best for bass?
The paper states that “the range of preferred bass levels among individual listeners is 17dB, from -3dB (listener 346) to 14.1dB (listener 400).” This finding astounded me, not only because of the range of difference of 17dB — a lot — but that someone out there preferred -3dB of bass cut.
What ohms are best for bass?
If you are looking for more bass, then you will want to go with a 4 ohm speaker. However, if you are looking for a more balanced sound, then a 2 ohm speaker is probably a better choice.
What phase should my sub be on?
To check your sub’s phase, play music with lots of bass, listen for a minute or so, and have a friend sitting by the sub flip the sub’s 0/180-degree phase switch slowly back and forth. The correct setting is the one that yields more bass.
What Hz should I set my sub too?
Subwoofers: 70-80 Hz (low pass), the most essential purpose of a subwoofer crossover is to block midrange sounds. Car main speakers: 50-60 Hz, the most critical element in main speaker crossovers is to block low-end bass (frequencies 80 Hz and below) 2-way speakers: 3-3.5 kHz (high pass)
What should the LPF be set to for subs?
As a general rule, the Low-Pass Filter should be set at a value approximately equal to (or below) 70% of your main speaker’s lowest frequency response. For example, your speaker’s frequency response goes down to 43Hz. 70% of 43Hz equals 30.1, so you should set the subwoofer’s low pass filter to 30Hz.
What frequency should subwoofers be at?
The typical frequency range for a subwoofer is about 20–200 Hz for consumer products, below 100 Hz for professional live sound, and below 80 Hz in THX-certified systems. Subwoofers are never used alone, as they are intended to augment the low-frequency range of loudspeakers that cover the higher frequency bands.
What Hz is best for deep bass?
The best Hz for bass is between 60-250 Hz, as recommended by professionals. These ranges protect speakers from damage and ensure optimal safety and listening experience for you. Listening to bass at too low a frequency outside of this range can damage hearing.
