A phono cable serves to connect the tonearm of a turntable to a phono preamp. This is the case in most Hi-Fi set-ups with a vinyl system.
Can I use any RCA cable for turntable?
The RCA cable that is often hard-wired to the turntable is short and low capacitance. It is a bad idea to change this cable using regular interconnect cables, it often causes a mis-match between the cartridge and the preamp with unwanted audible side effects.
Is RCA same as phono?
Is there any difference in using the names RCA and phono now? RCA and phono are still the same in terms of the connector design. But as technology advanced, the RCA connector began to be used not only for phonographs but also for many other devices such as TVs, VCRs, DVD players, and so on.
Can I connect turntable directly to speakers?
A few powered bookshelf speaker pairs, such as the Klipsch R-51PM, have phono inputs, so they can connect directly to turntables that lack phono preamps. But with most powered speakers, you need to use a turntable with a built-in phono preamp or connect an external phono preamp between the turntable and the speakers.
What cable do I need for turntable? – Related Questions
Can I plug a turntable into aux?
Simply plug the turntable’s audio signal cable into one of the receiver’s analog audio inputs. These inputs are oftentimes labeled Aux (auxiliary), Line In, Analog In, etc. You can even use your receiver’s “CD” or “Tape” input, if needed. No other connections are required.
How do I connect turntable to speaker wire?
Connect the RCA (red and white) plugs from the turntable cable to the RCA (female) to 3.5 mm (1/8″) mini-plug (male) adapter cable, making sure to match red plug to red plug and white to white. Then connect the adapter cable’s 3.5 mm mini-plug to the powered speakers’ Line Level* input.
What do I need to hook up turntable to speakers?
You will only need a few things to set up your passive speakers correctly with a turntable: a receiver, phono pre-amp, RCA cables and a pair of speakers. While there are more components to setting up passive speakers than powered speakers, the process really isn’t much more involved.
Why wont my speakers work with my turntable?
Confirm your speakers or amplifier are powered on. If the stylus protector(1) is still on the stylus(2), remove it before playback. Ensure the stylus does not come off with it. Check your tonearm balance, without the correct tracking weight, the stylus will not track in the grooves of the record.
What is RCA output on record player?
It means that your record player is equipped with a phono preamp that takes the phono signal and converts it to the line signal needed for a connection to an amp or active speaker. All you need with one of these turntables, is one of those well-known, red-and-white RCA (Cinch) cables and voila, sound!
How do you connect a turntable to a soundbar?
Connect the turntable audio cables to the separate phono preamp, and any other wire your turntable has. Then, connect the phono preamp audio cables to the receiver’s analog inputs (your soundbar) Finally, connect the phono preamp to its power supply and switch on.
Can I use speaker wire for a turntable ground?
Speaker wire won’t work as a ground wire because the gauge is too small.
How do you connect speaker wire to spring clips?
For spring clip terminals, press down on the red (positive) or black (negative) clips and insert the speaker wire into the slot. Then, release the clips. For binding post terminals, loosen the red (positive) or black (negative) binding posts by turning them counter-clockwise.
What is a banana plug for speakers?
So named for its resemblance to a favorite source of potassium and pratfalls, the banana plug is used to finish off the exposed ends of speaker wire and make them easier to plug into your receiver or speakers.
Does it matter which wire goes to which terminal on a speaker?
It doesn’t matter which way round you connect the wires – even if the wire is marked with a plus and minus. Just make sure that the same piece of wire is connecting the positive and negative terminals on the amplifier and speaker. Below you can see the binding posts on the rear of an AV receiver.
What is a spring clip connector?
The SPRING CLIP CONNECTOR snaps the chain firmly together. Compatible with all brands of single-speed chains. Recommended for OEM use. Color. Silver/Black.
What are banana wires?
A banana connector (commonly banana plug for the male, banana socket or banana jack for the female) is a single-wire (one conductor) electrical connector used for joining wires to equipment.
Why are they called banana clips?
Banana plugs are called bananas because of the metal leaves which bulge out. Each leaf is curved like a banana. These are most commonly either 4 leaves or 9 leaves. The 9 leaf bananas have a stronger “grip” on the socket and are preferable for heavier wires or in high voltage uses where safety is a concern.
Can banana plugs be used with spring clips?
Standard Banana Plugs won’t work with Spring Clip Terminals. The Deadbolt Flex Pin Connectors are designed to fit in terminals just like regular speaker wire would.
Is it better to use banana plugs or bare wire?
Bare wire connections can easily get pulled out, become corroded, or get frizzy over time, making it hard to guarantee a secure connection. Banana plugs protect against corrosion and ensure a solid connection with the maximum surface area for the life of your cable.
