External bass controls (EBC), or remote bass controls (RBC), are a convenient and easy to install accessory that allows you to tune the bass in your music song by song.
If you’re looking for a subwoofer that will give your system a kick in the pants, Planet Audio subwoofers are a good choice. Their subs are affordable, durable, and powerful.
Is Planet Audio a good brand?
Good quality sound for a good price. Stylish design with a lighted logo makes it look better than the average amps. Planet Audio is a good brand as I have tested this amp, a 1 channel amp, 12″ subs, 3-way 6×9, 6 1/2 combos, and their 10 farad cap no problems at all.
How do you tune a planet audio amp?
What does a remote subwoofer level control do? – Related Questions
How do I adjust my subwoofer?
Subwoofer Settings
Before playing the subwoofer, adjust the crossover.
Turn on the power and set the subwoofer volume to the desired level.
Adjust the phase control if it’s available.
Make minor adjustments to the stereo audio equalizer for preferred sound.
What frequency should I set my amp to for subs?
Subwoofers: 70-80 Hz (low pass), the most essential purpose of a subwoofer crossover is to block midrange sounds. Car main speakers: 50-60 Hz, the most critical element in main speaker crossovers is to block low-end bass (frequencies 80 Hz and below)
What should the settings on my amp be?
Generally, good rock guitar amp settings are:
Gain: 5-7.
Treble: 5.
Mids: 6.
Bass: 6.
How do you set a good sound amplifier?
Turn the receiver volume down. Set the receiver’s fade control all the way to the rear speakers. Again, turn the receiver’s volume up to ¾ full and turn up the rear gain control of your amp until the music distorts, then turn it down so it plays clean again. Turn the receiver volume down.
How do I get my planet amp out of Protect Mode?
How to Get Amp Out of Protection Mode:
Disconnect Speakers.
Check the Temperature of the Amp.
Unplug the Head Unit.
Check the Ground Connection.
Check All Cables.
Check Impedance Load.
Reset the Amp’s Gain.
How do you set up an amplifier?
Your Step-By-Step Guide
Step 1: Disconnect the Car Battery.
Step 2: Mount the Amp.
Step 3: Install the Power Wire.
Step 4: Install the Fuse Holder.
Step 5: Connect the Power Wire.
Step 6: Install the Ground Wire.
Step 7: Plug in RCA, Speaker, and Remote Turn-On Leads.
Step 8: Turn It On.
How do you adjust a subwoofer amp?
Turn your sub amp’s gain to its lowest, most counter-clockwise position.Switch its low-pass filter on and set it as high, clockwise, as it will go. If it has a bass boost, turn it off.
What frequency is best for bass?
The best Hz for bass is between 60-250 Hz, as recommended by professionals. These ranges protect speakers from damage and ensure optimal safety and listening experience for you. Listening to bass at too low a frequency outside of this range can damage hearing.
Where does the remote wire go on a amp?
Some of the more common options for connecting the remote turn on wire when using a factory head unit are to the wire connected to a power antenna (older vehicles which do not turn off the antenna when not using the radio) or to the vehicle’s fuse box.
Does the remote wire turn on the amp?
Do I need remote turn on wire for AMP?
You must supply the amp’s power and ground wiring, an inline fuse, a remote turn-on wire, RCA cables, and speaker wires.
How do I turn on my amp without remote wire?
Do you turn amp on first or last?
Always, always turn off your amp before your other gear. If you want to be able to flip one switch to power your studio on and off there are a few companies who make sequential power units (ETA, Furman, and Juice Goose are three I know of).
Can you use any wire for remote wire?
you can use speaker wire for that. Just run the remote wire off your other amp. any copper wire will work it doesnt matter how old or new it is. just find some old copper wire and use it.
Can you connect your phone to your amp?
Audio cables
One of the most basic ways to connect your smartphone to your home stereo system is using a 3.5 mm to RCA stereo audio cable. One end plugs into your smartphone’s headphone jack, and the RCA connections connect the stereo amplifier, receiver, or speaker.
How do I connect my phone to my subwoofer?
You place your smartphone on top of the subwoofer with the bottom portion (where the microphone is usually located) facing one of the drivers. The subwoofer will then play a test tone to calibrate your phone.
