What is a good crossover frequency for 3-way speakers?

For 3-way speakers: the recommended crossover frequency is 500 Hz and 3.5 kHz. The midrange drivers in a 3-way system most likely won’t deliver quality sounds below 500 Hz or 250 Hz.

What is a 3-way speaker crossover?

A 3-way crossover is constructed as a combination of low-pass, band-pass and high-pass filters (LPF, BPF and HPF respectively). The BPF section is in turn a combination of HPF and LPF sections.

What does a 3-way crossover do?

A crossover serves as a filter that blocks out unwanted frequencies to a speaker or group of speakers. This is extremely useful because it allows us to specifically send each speaker the group of frequencies that it will play most efficiently and effectively.

What is a good crossover frequency for 3-way speakers? – Related Questions

Do I need a passive crossover?

If your car audio system uses coaxial speakers, you probably don’t need an additional crossover. Full-range speakers already have built-in passive crossovers that filter the frequencies that reach each driver. Even if you add an amplifier into the mix, the built-in speaker crossovers should be more than sufficient.

Is active crossover better than passive?

Passive crossovers don’t need power to filter the signal as desired. Active crossovers require power and ground connections, but give you much more flexibility and fine-tuning control over your music.

What is the difference between 2-way and 3-way crossover?

A 2-way speaker has two types of drivers which are known as a woofer and tweeter. The woofer is a speaker built exclusively for low-frequency sounds, while the tweeter is designed for high-frequency sounds. A 3-way speaker generates sound from three individual devices known as the mid-range, woofer and tweeter drivers.

What are the benefits of a crossover?

Since they are built on unibody frames like road cars, crossovers usually offer a smoother, more comfortable ride, handle better, are easier to maneuver and park and tend to stop quicker than regular SUVs.

Why do I need a crossover?

Why Do You Need A Crossover? Every audio system, including the one in your car, needs a crossover to direct sound to the correct driver. Tweeters, woofers and subs should get high, mid and low frequencies respectively. Every full-range speaker has a crossover network inside.

How does a crossover affect phase?

The phase shift caused by the crossover filters affects two things: The ability of the crossover/loudspeaker system to reproduce transient-type (pulse) waveforms. The flatness of the combined acoustical output of the two (or more) drivers. The radiation angle of the loudspeaker’s output.

Which order crossover is best?

Crossovers are described as having an ‘order’, 1st order, 2nd order, 3rd and 4th. The number denotes the strength of the filter, with 1st being the weakest and 4th the strongest. A 4th order filter, for a woofer, would feature 4 components, typically 2 inductors and 2 capacitors.

How can I make my crossover more effective?

Does a crossover go before or after the amp?

An active, or electronic crossover goes between the receiver and the amp. It handles low-level preamp signals with its solid-state circuitry to cleanly divide the signal and send each band of frequencies in the right direction.

Where do you put the passive crossover?

Passive crossovers for component speaker systems are very simple to install. They each go between your amplifier and a speaker and do not require a power connection, a turn-on lead, or grounding. You connect the speaker wire coming from your amp to the crossover’s input.

What should my crossover be set on my amp?

Set the crossover point around 10 Hz below the lowest frequency your speakers can produce without issue. (keep in mind that the most common recommendation for crossover frequency is 80 Hz).

What crossover should I set my subwoofer?

What is the recommended crossover frequency for a subwoofer? For home theater systems, 80 Hz is the recommended setting and the default setting out of the box. However, you can set the channel’s crossover between 40 Hz – 250 Hz based on which setting sounds best for your system.

How do you get a punchy bass on a subwoofer?

What frequency is best for bass?


For normally tuned bass guitar and upright double bass, note fundamentals extend down to E1, (open E). I would consider bass arbitrarily to be below C2 (65.41 Hz). That is two octaves below middle C. The fundamental of a note is its musical pitch.

What happens if you set crossover too high?

The main drawbacks with too high a setting are that the stereo image can suffer as the sub’s frequencies enter the normal hearing range (you can localize the sub, you can tell where it is as a source distinct from the main speakers), and the sub may distort and/or roll off higher frequencies than it can handle.

Leave a Comment