What is rel high level input?

The high-level, unbalanced, dual-channel (stereo) input is via a Neutrik® Speakon® connector which is connected to the power amplifier’s left and right channel speaker terminals. This has the advantage of ensuring that the REL receives exactly the same signal as the main speakers.

Should I leave my REL subwoofer on all the time?

Yes you can leave your subwoofer on all the time as long as it has an auto standby feature. Subwoofers in standby last longer & use less power. Older subwoofers that don’t have this function should be turned off when not in use as electricity escapes in the form of heat, causing the amplifier to get hotter than normal.

Where do I run my REM wire?

Some of the more common options for connecting the remote turn on wire when using a factory head unit are to the wire connected to a power antenna (older vehicles which do not turn off the antenna when not using the radio) or to the vehicle’s fuse box.

What is rel high level input? – Related Questions

How do you run a REL subwoofer?

We use cut #4 from the soundtrack to Sneakers, the movie. Once the system is up and running with your break-in cut, run it at moderate volume for around 15 minutes or so. This allows everything in the amplifier and driver time to adjust and begin warming up. This is an often-overlooked phase of break-in.

How do you ground a REL subwoofer?

Instead of connecting the BLACK wire of the high level cable, simply make a connection between an unused RCA on your system and the LFE input on the REL. The outer rings of the RCA will connect the REL to signal ground of the system.

How do I connect REL to Class D?

How do you set up a REL crossover?

What crossover setting gives you most bass?

Tips for Setting the Proper Crossover Frequency of a Subwoofer
  • If you know your speaker’s frequency range, set the crossover point roughly 10 Hz above the lowest frequency your speakers can handle cleanly.
  • The most common crossover frequency recommended (and the THX standard) is 80 Hz.

Should I set my subwoofer to 80Hz?

80hz tends to work best in most systems for a variety of reasons. But smaller speakers will often begin to sound strained / harsh much lower than 120hz or even 150hz. This is particularly true at louder volume levels.

What Hz should my crossover be?

Recommended Crossover Frequencies

Car main speakers: 50-60 Hz, the most critical element in main speaker crossovers is to block low-end bass (frequencies 80 Hz and below) 2-way speakers: 3-3.5 kHz (high pass) Midrange: 1-3.5 kHz. 3-way system: 300 Hz and 3.5 kHz.

What Hz is best for subwoofer?

What is the recommended crossover frequency for a subwoofer? For home theater systems, 80 Hz is the recommended setting and the default setting out of the box. However, you can set the channel’s crossover between 40 Hz – 250 Hz based on which setting sounds best for your system.

What Hz is best for audio?

There we go: the best frequency for audio sampling is around 40Khz. And talking about industrial standards, we have the mighty 44.1 Khz at our disposal. Summarizing: The best frequency for recording, post producing and reproducing music is 44.1 Khz.

Is 50hz enough bass?

50 Hz is too high. You can use the Low Cut option of M-Class EQ, which cuts at 30Hz. If you can’t hear 50hz, its hard to mix it. And 50hz should be a subwoofer.

Can humans hear 50 Hz?

Measured in hertz (Hz), a healthy ear can hear a wide range of frequencies, from very low (20 Hz) to very high (20,000 Hz).

How many Hz is best for bass?

Audio Frequency Subsets
Frequency SubsetFrequency Range
Bass60 to 250 Hz
Lower Midrange250 to 500 Hz
Midrange500 Hz to 2 kHz
Higher Midrange2 to 4 kHz

Which is faster 50Hz or 60Hz?

Speed. For most standard motors, the RPM is proportional to the frequency, which means there is a speed increase when you use 60Hz versus 50Hz. In fact, 60Hz can be up to 20% faster.

What happens if you plug 50Hz to 60Hz?

When a 50Hz single phase motor is brought to 60Hz the start function can be upset because the motor reaches the centrifugal switch speed 20% earlier than normal. When it does, the starting torque of the motor is suddenly reduced. It could fail to speed up further and never reach normal running speed.

Leave a Comment