Located in Shenzhen, China, SMSL Audio was founded in 2009 with in-house R&D, manufacturing and marketing expertise, and specialise in audio DAC, stereo headphone amplifier and power amplifier products.
Connect AC power adapter to rear power jack, then connect power adapter to wall outlet.
Connect a cable from your audio player to the RCA or 3.5mm input jack.
Connect headphones to the front headphone output jack.
Turn the volume knob clockwise to power on.
What should you not do with an amp?
Never, never, never run the amp with no speaker plugged in. This can cause major damage. Do not flip the power switch off, then back on rapidly. This can cause power supply damage.
Do I connect my amp with positive or negative?
Attach the power cable to the positive battery terminal (not directly to the battery post itself).
Where is Smsl made? – Related Questions
How do I connect my amplifier?
How to Connect Speaker to Amplifier: Step by Step
Connect the end of the speaker wire that corresponds to the back of the amplifier.
Connect the speaker wire to the speaker.
If the speaker and the amplifier are correctly connected, you can now plug the amplifier into the power source and enjoy your speakers.
How do you hook up an amp to a stock radio?
The best way to connect it to a factory system is to tap into the stereo’s speaker outputs for the amp’s input signal.Then send the amp’s outputs back to the stereo’s harness, and on to the speakers through the factory wiring.
What do I connect the amp turn on wire to?
How do I connect amp to speaker terminal?
To connect:
Unplug and turn off all components.
Ensure you are plugging the positive connector into the positive terminals and the negative connector into the negative terminals (on both your speaker and your amplifier).
Securely push plugs into terminal. That’s it!
Does it matter which wire is positive and negative for speakers?
Good news is, with speakers it doesn’t really matter which one you choose as your positive and which as your negative, just so long as you are consistent. Ultimately, what you want is for the wire that connects to the red terminal on your Amp or Receiver to connect to the red terminal on your speaker.
Can I connect speaker directly to amplifier?
Simply connect your speakers to the pre-outs or zone 2 outputs. Plug one end of the speaker cable for the right speaker into the right speaker output jack on the back of the stereo amp. Speaker wires are most commonly found as bare, meaning that you would use a wire stripper to expose the strands at the ends.
Can you put two speaker wires into same receiver hole?
If each speaker has an impedance of 8 ohms or more, then you can generally connect them in parallel. If each speaker has an impedance below 8 ohms, you should wire them in series.
Are speakers louder in series or parallel?
Speakers are always louder when wired in parallel. Series wiring leads to more impedance and thus less voltage per speaker which translates to less volume per speaker. A parallel circuit reduces the resistance and impedance on each speaker and equates to more volume.
How many speakers can a 4 channel amp power?
For example, a 4 channel amplifier may be able to power up to 8 speakers. In fact, if you wire it correctly, you will be able to pull up to twice as much power out of the amp. First, you need to make sure your amplifier can be safely set up this way.
Is it OK to daisy chain speakers?
An important note: In most cases, it’s not advisable to daisy chain more than two pairs of speakers to a single output. Doing so could end up damaging the equipment.
Can I connect 4 speakers to 2 channels?
A lot of people assume that they can only connect a couple of speakers to a 2-channel amp. This is not always the case, and in this guide we’re exploring how to connect 4 speakers to a 2-channel amp. There are numerous ways to do this, using a series or a parallel configuration for your speakers.
Can I power 4 speakers with a 2 channel amp?
You can easily connect 4 speakers to a 2 channel amplifier just by keeping in mind the impedance of speakers and dividing the power equally to both the channels. There are both methods available to connect 4 speakers i.e series and parallel.
Can I use 2 amplifiers on the same speaker set?
You can use different amplifiers together, but there are a few things you need to keep in mind. Make sure that both amplifiers have the same impedance rating. If they don’t, one amplifier will be working harder than the other, and this could cause damage to your speakers or amps over time.
What happens if your speakers are more powerful than your amp?
A: It doesn’t have to be, but it doesn’t hurt if it is. That will give you more headroom, and that’s always a good thing. However, huge discrepancies could cause a problem, and you may damage your speakers if the amount of power sent from your amp is way higher than your speaker can handle.
What happens if amp is too powerful for speakers?
Speakers and too powerful amps when connected with a continuous power rating, make the speakers struggle. The speaker will not be able to distribute the heat energy from the amplifier and then it will tend to burn off the speaker’s voice coil.
